Archived posting to the Leica Users Group, 1999/07/08
[Author Prev] [Author Next] [Thread Prev] [Thread Next] [Author Index] [Topic Index] [Home] [Search]Richard (the original poster) had great negatives, wonderful prints but practically invisible frame numbers. I would say, as long as the prints are wonderful, why worry? As negatives may look different depending on the developer used, I never compare negatives after a film test. The proof of the pudding is in looking at the prints. I am glad Richard got wonderful prints. Like Greg, I need longer development times than those stated in Kodaks (excellent) tables. Somebody wrote here that the time compensation Greg refers to is only needed when the number of films stated are developed at the same time, and that he had this information from somebody who had called Kodak and had been told so. This may be so. I still need longer development times than the table states. Actually I need exactly those times I get when I apply the compensation factor...... You will only get development times that are valid for YOU (and your method of measuring exposure times and developing) by making a test. It is really worth the time to test out a film, three different development times should be enough, and in each case shoot series of exposures from plus two stops to minus two stops. But do not change any variable such as agitation, thermometer etc etc. BTW one good reason to use Xtol is that it is environment friendly. There is a similar developer for prints, the Agfa Neutol PLUS which I have been using for the last year and since then I use my fingers for pulling the prints out of the developer >Hello Luggers. >I've struggled with the amount of XTOL needed per roll of 135-36 film for >some time, and I have been given a variety of opinions despite the fact that >we all read the same directions. In the Kodak technical sheet J-107 which >deals with XTOL for use in small tanks and trays there is a time >compensation table which indicates that no time compensation is needed for 1 >to 5 rolls per liter of full strength developer. I read that as meaning that >up to an amount of 200 ml/roll no time increase is needed. For 6 to 10 >rolls/liter, the development time should be increased by 15%. As 10 >rolls/liter is 100 ml /roll, wouldn't that indicate a 15% increase in >development time for the often quoted amount of 100 ml/roll? > >I'll join those who praise the qualities of XTOL. It truly is a remarkable >developer with fine grain and consistent results. > >Regards, >Greg Achenbach >-----Original Message----- >From: Dennis Warters <dbsvideo@gci-net.com> >To: leica-users@mejac.palo-alto.ca.us <leica-users@mejac.palo-alto.ca.us> >Date: Wednesday, July 07, 1999 12:43 PM >Subject: RE: [Leica] XTOL Again (slightly off-topic) > > >>Remember to use the Kodak recommended amount of 100ml of stock developer >per >>roll. >> >>-----Original Message----- >>From: owner-leica-users@mejac.palo-alto.ca.us >>[mailto:owner-leica-users@mejac.palo-alto.ca.us]On Behalf Of Edward >>Meyers >>Sent: Wednesday, July 07, 1999 10:57 AM >>To: leica-users@mejac.palo-alto.ca.us >>Subject: Re: [Leica] XTOL Again (slightly off-topic) >> >> >>The edge marking density is usually an idication of your development. >>If the density of the edge markings are very weal, then it would >>mean that you underdeveloped the film. What was your temperature >>of developer? Dilution? etc. Ed >> >>On Wed, 7 Jul 1999, Richard E. Baznik wrote: >> >>> Yesterday I processed a roll of TMX in XTOL for the first time (shot in >an >>> M6 with Tri-Elmar and thin Tele-Elmarit, so we have some relevance to the >>> LUG). I shot at EI 100, and used a 1:3 dilution for 13 minutes at 74F. >>> Great negatives, wonderful prints. >>> >>> One question, however. The frame numbers and other Kodak verbage on the >>> edges of the film are practically invisible. Is this a common trait of >>> XTOL? I've never had that result with any other developer, and I've used >>> quite a few. It is slightly inconvenient, but I'll live with it if that's >>> the price of getting negatives like these. >>> >>> Anyone have a similar experience?///REB >>> >>> >>> >>> Richard E. Baznik >>> Vice President for Public Affairs >>> Case Western Reserve University >>> 10900 Euclid Avenue, Cleveland, Ohio 44106-7021, U.S.A. >>> Voice: (216) 368-2338 >>> Fax: (216) 368-6674 >>> >>> >> - -- christer almqvist eichenstrasse 57, d-20255 hamburg, fon +49-40-407111 fax +49-40-4908440 14 rue de la hauteur, f-50590 regnéville-sur-mer, fon+fax +33-233 45 35 58